Commercial Leak Detection: Finding Water Loss on Business Premises
Night-flow tests, zoning with sub-meters and valves, then pinpointing under car parks and loading bays: how water loss is found on business sites.
On a business property, a water leak is rarely a single dripping pipe. Larger sites have long underground mains, several buildings, fire lines, irrigation, process water and sometimes dozens of sub-meters. Water can be lost for months before anyone notices, and when the bill finally jumps, nobody knows where to start looking.
Commercial leak detection is about finding that loss systematically, with as little disruption to the business as possible.
Signs a Business Property Is Losing Water
- The municipal bill has risen without a matching increase in staff, production or occupancy
- The bulk meter moves overnight or over weekends when the site is closed
- Sub-meter readings don't add up to the bulk meter
- Wet ground, sinkholes, or paving that keeps subsiding near buried lines
- Low pressure at the far end of the site
- Damp walls, stained ceilings or mould in specific areas
On sites on dolomite, including parts of Centurion, escaping water is also a sinkhole risk, which makes finding it urgent.
Step 1: The Night-Flow Test
The simplest and most useful test on a commercial site is a night-flow test. Read the bulk meter when the site closes and again before it opens, or read it at short intervals when use is at its minimum. Whatever flows when the building is empty is either legitimate night use (cooling towers, cleaning, irrigation) or a leak. Our guide to the night-flow test explains how to run it yourself.
Step 2: Divide and Measure
Once loss is confirmed, the site is split into zones. Where sub-meters exist, comparing their readings with the bulk meter shows which part of the site is losing water. Where they don't, valves are closed in sequence, building by building or line by line, while the bulk meter is watched. The zone whose isolation stops the loss contains the leak.
Step 3: Pinpoint the Leak
Within the zone, the leak is located from the surface:
- Acoustic correlation and ground microphones on metal and ductile-iron mains
- Tracer gas on plastic mains, under paving, tar and concrete
- Thermal imaging for hot-water and heating lines inside buildings
- Pressure testing of isolated lines, including fire lines and irrigation
The leak is marked so excavation is small and targeted, which matters a lot under car parks, loading bays and roads.
Common Leak Points on Commercial Sites
- Underground mains between buildings, often decades old
- Fire-water lines and hydrant connections, which are pressurised but rarely inspected
- Irrigation systems on landscaped grounds
- Ablution blocks: cisterns, urinal flush valves and taps
- Kitchens and process water in restaurants and factories
- Cooling towers and plant rooms
Working Around the Business
Commercial detection is planned to keep the site running. Most of the work happens from the surface, outside trading hours where needed, and isolation is done in short, scheduled windows. You get a written report with the leak locations, the evidence and repair recommendations, which is also what insurers, landlords and trustees need.
Who It's For
Offices and office parks, factories and warehouses, schools, churches, hospitals, shopping centres, hotels and guest houses, body corporates and estates. For residential complexes, see our guide on leak detection for body corporates and estates.
Commercial jobs are scoped per site. See our commercial leak detection service for how to get a site survey and quote.
Frequently Asked Questions
Q: How long does commercial leak detection take? A: It depends on the size of the site and the number of zones. A small office may take a few hours; a large site with several buildings may need more than one visit. The scope and time are agreed before work starts.
Q: Do we need to close the business? A: Usually not. Most testing happens from the surface, and short isolation windows can be scheduled outside trading hours.
Q: Can you find leaks on fire lines? A: Yes. Fire lines are pressurised and often run underground for long distances, and they can be pressure-tested and pinpointed like any other line, in coordination with your fire-safety provider.
Q: Will the report help with a municipal billing dispute? A: Yes. A report showing the leak location, meter readings and the repair supports a query or leak-allowance application with the municipality.
